Boromir Bastard Sword from the Lord of the Rings
A bastard sword bridges the one-handed arming sword and the two-handed longsword. The 20 cm grip gives you room for a second hand when you want leverage, while the sword stays light enough to carry and cut with one. This Boromir Bastard Sword is forged from 5160 spring steel and built for drilling and controlled test-cutting rather than wall display.
Boromir Bastard Sword vs. the Blade Truth StandardÂ
Steel Truth
5160 spring steel earns its place in the functional sword world because it survives impact. The chromium and silicon content give the blade high toughness and a spring temper, so it flexes under load and returns straight.
Tempered to a working hardness in the low 50s HRC, the edge holds through repeated cuts while the spine absorbs shock instead of chipping. This is the steel makers reach for when a blade has to take real edge-on-target contact and keep its geometry.
Build Truth
The blade runs 71 cm with a distal taper from 5 mm at the guard down to 3.1 mm near the tip. That taper strips mass from the forward blade and pulls the point of balance to just 4 cm ahead of the guard. The sword feels hand-forward and lively as a result, closer to the reflexes of an arming sword than the momentum of a long two-hander.
Overall length is 93 cm. The bare sword weighs 1.6 kg, or 2.1 kg with the scabbard. The 19.5 cm guard gives full hand coverage in the bind.
Use Truth
The short blade and near-hilt balance make this sword quick in the hand. Point control comes easily, thrusts recover fast, and guard transitions cost little effort. Bring the second hand onto the rear of the grip and you add leverage for binds and heavier cuts without surrendering much speed.
It suits solo form work, and light-to-moderate test cutting against water bottles and tatami mats. Longsword practitioners who want a shorter, faster blade for tighter spaces will find it easy to command.
Limit Truth
This is a Boromir bastard sword, and the numbers say so plainly. The 71 cm blade sits at the short end of the category, and the balance point rides closer to the hand than most dedicated cutters, so the blade carries less forward mass through a stroke. You trade cutting authority for agility. Heavy chopping through thick targets calls for a longer blade with a more forward balance.
Care for the edge the way any functional blade demands: keep it oiled, store it dry. It performs as a training and cutting tool that rewards proper maintenance.
Good products create sales. Clear standards create trust. Trust creates authority.
Specifications of Boromir Bastard Sword
- Overall Length: 93 cm (36.61″)
- Blade Length: 71 cm (27.95″)
- Grip Length: 20 cm (7.87″)
- Guard Length: 19.5 cm (7.68″)
- Sword Weight: 1.6 kg (3.53 lbs)
- Weight with Scabbard: 2.1 kg (4.63 lbs)
- Blade Thickness: 5 mm → 3.1 mm (0.20″ → 0.12″)
- Point of Balance: 4 cm (1.57″) from the guard
- Blade Material: 5160 Spring Steel
Frequently Asked Questions
Is this Boromir bastard sword one-handed or two-handed?
Both. The 20 cm grip is a hand-and-a-half length. So you can fight one-handed for speed or add a second hand for leverage and stronger cuts.
Is 5160 spring steel good for a functional sword?
Yes. 5160 is a low-alloy spring steel valued for toughness and shock resistance. It takes a spring temper that lets the blade flex and recover, which makes it a common choice for cutting swords and battle-ready reproductions.
Can you cut with Boromir Bastard Sword?
Yes, within its design. It handles light-to-moderate test cutting on soft targets such as bottles and tatami. The near-hilt balance favors speed over heavy chopping.
How does it compare to a longsword?
It uses the same hand-and-a-half grip principle but with a shorter, faster blade. Expect quicker point work and easier one-handed use, with less reach and less cutting mass than a full longsword.
Check out the other Boromir sword model.Â










